Skip to main content

Eduardo's Criticism

Coming out of retirement.
When Eduardo authored this typecast he was using a less-than-svelte Remington Performer. When he was working on the second draft I pulled out the "retired" Hermes 3000 and suggested that he try using it for the second draft. His experience was far better when he used the Hermes. On reflection, Eduardo said that if the Hermes was the one he started with his opinion would be much different. I think that goes to show that perceptions of the typewriter can be informed by the machine that had been used. If your typewriter was really nice you would have fond memories of the experience. If it was a terrible, clangy, Adler J5-like machine you might have a totally different response.


Comments

  1. Resonance here :-) I have an Underwood 4 (in bits), an SM3 and an Everest K2 at arm's reach from the dining room table. My son chirps up, "Daaaad, can you get the little green one out of the attic? I need to do an essay for homework". He likes the light touch of the Antares, even though you have to keep an eye on the short ribbon which needs manually reversing every page or so.

    ReplyDelete

Post a Comment

Popular posts from this blog

How To: Cleaning Wrinkle Paint

You either love wrinkle paint or you put up with it hoping that a machine in shiny black comes your way. I happen to love the finish. It's very rugged, hides a myriad of metalwork sins, and can come in some very sober and serious colors. As great as I think this paint is, it is a magnet for dirt, grime, and crud. Dirt invariably make its way into the wrinkles and makes your typewriter look tired and grungy. However, the innate ruggedness of the paint makes it easy to clean. This is the process I use. Your mileage may vary. 
To start with you need some simple supplies. A couple of soft cloths, a small Tupperware container, a household laundry detergent without dyes or perfume, an old toothbrush, a utility spray bottle, and a blue Olympia SM3 (or whatever you happen to have). As with the other How-To, I recommend you dust/wet-dust your typewriter first. It takes a minute and "Water is the best solvent."


This process assumes that your typewriter is clean on the inside. There …

The Most Beautiful Typewriter

When the Olympia arrived in the mail, I immediately wanted one for myself. I began the process of looking for a light blue SM3. Surprisingly, I was able to to find one here in Phoenix in an identical color. It really is a very attractive typewriter. I thought this was, perhaps one of the most beautiful typewriters in the world. The color is blue like a summer sky. The chrome shines even on the grayest of days. The gentle lines are at once playful and very serious. It is a joy to look at.

But as lovely as the Olympia is, there's only one typewriter that I think truly deserves the moniker of "The Most Beautiful Typewriter" and that is the Olivetti Studio 42 designed in 1935. I know many will disagree with me. I would love to hear the disagreements.

I  do not have an Olivetti Studio 42, but I dream of owning one. If I found this machine (in good condition) I would stop collecting. It's that special.

To assist in proving that the Olivetti Studio 42 is "The Most Beaut…

Pinhole MG Filter Adapter

A few months ago a friend gave me an old set of Ilford multigrade filters he used in college. He thought I would get some use out of them in my home darkroom. It's nice to have this set. They are good for a couple of really cool contrast techniques in darkroom printing on multigrade paper. It can really save your bacon with a difficult print.

I wanted to also use these filters with my pinhole camera and multigrade paper. The contrast with the paper negatives can be a little extreme and these filters can tame contrast. However, my filters can't easily be taped to the front of the camera. I had to devise a method to hold them.

The 3 inch filters are designed to go under the lens on a darkroom enlarger. Each filter is mounted in a plastic holder that slides into a corresponding mount attached to the enlarger. I pulled out my calipers, did a little measuaring, and crafted a design in Tinkercad. A hours later and I had this design:


I decided to print it in two pieces on my Monopric…